19-5299; rev 1; 10/12 general description the max16833 evaluation kit (ev kit) provides a proven design to evaluate the max16833 high-voltage hb led driver with integrated high-side current sense. the ev kit is set up for boost and buck-boost configurations and operates from a 5v to 18v dc supply voltage. the ev kit is configured to deliver up to 1a to one string of leds. the total voltage of the string can vary from 3v to 36v. the anode of the led string should be connected to the led+ terminal. the cathode of the led string can be connected either to the pgnd (boost mode) or led- (buck-boost mode) terminal. in the case of the boost mode, the input voltage should not exceed the led string voltage. the ev kit pcb comes with a max16833aue+ installed, which is the frequency-dithering version. the ev kit also comes with the pin-compatible max16833baue+, which is the reference-voltage output version. features s configured for boost and buck-boost s analog dimming control s proven pcb layout s fully assembled and tested component list +denotes lead(pb)-free and rohs compliant. ordering information part type MAX16833EVKIT+ ev kit designation qty description c1 1 22ff q20%, 50v electrolytic capacitor (6.3mm x 7.7mm) sun electronic 50ce22pc c2, c5, c13, c14 4 4.7ff q10%, 100v x7r ceramic capacitors (2220) murata grm55er72a475k c3, c4 2 1ff q10%, 16v x7r ceramic capacitors (0603) murata grm188r71c05k c6, c11, c15 3 4.7ff q10%, 50v x7r ceramic capacitors (1210) murata grm32er71h475k c7, c10 2 0.1ff q10%, 16v x7r ceramic capacitors (0603) murata grm188r71c104k c8 1 680pf q5%, 50v c0g ceramic capacitor (0603) murata grm1885c1h681ja01d c9 1 33000pf q10%, 16v x7r ceramic capacitor (0603) murata grm188r71c333ka01d designation qty description c12 1 4.7ff q10%, 25v x7r ceramic capacitor (1206) murata grm31cr71e475m c16 1 0.1ff q10%, 50v x7r ceramic capacitor (0603) murata grm188r71h104k c17 1 22pf q10%, 50v c0g ceramic capacitor (0603) murata grm1885c1h220j c18 1 1000pf q10%, 50v x7r ceramic capacitor (0603) murata gcm188r71h102ka37d d1 1 100v, 3a schottky diode (smc) vishay 30bq100trpbf d2 1 75v, 15ma diode (3 sot323) diodes inc. mmbd4148w d3 0 not installed, diode (3 sot323) d4 1 40v, 350ma schottky diode (3 sod323) diodes inc. sd103aws-7-f ju1, ju2 2 2-pin headers ju3 1 3-pin header evaluates: max16833/max16833b max16833 evaluation kit for pricing, delivery, and ordering information, please contact maxim direct at 1-888-629-4642, or visit maxim integrateds website at www.maximintegrated.com.
2 note: indicate that you are using the max16833 when contacting these component suppliers. component suppliers component list (continued) *ep = exposed pad. supplier phone website diodes incorporated 805-446-4800 www.diodes.com international rectifier 310-322-3331 www.irf.com irc, inc. 361-992-7900 www.irctt.com murata electronics north america, inc. 770-436-1300 www.murata-northamerica.com sun electronic industries corporation 619-661-8288 www.sunelec.co.jp sumida corp. 847-545-6700 www.sumida.com vishay 402-563-6866 www.vishay.com designation qty description l1 1 9.5fh, 8.5a inductor (14.9mm x 14.9mm) sumida cdep147np-9r5mc-95 m1 1 100v, 42a n-channel mosfet (dpak) international rectifier irlr3110zpbf m2 1 100v, 12a p-channel mosfet (d 2 pak) vishay sihf9530s m3 0 not installed, mosfet (dpak) r1, r16 0 not installed, resistors (0603) r1 is shorted by pc trace; r16 is open r2, r14 2 0.05i q1% sense resistors (2512) irc lrc-lr2512lf-01-r050-f r3 1 536ki q1% resistor (0603) r4 1 0.2i q1% sense resistor (2010) irc lrc-lr2010lf-01-r200-f r5, r8 2 10ki q1% resistors (0603) designation qty description r6 1 22i q1% resistor (0603) r7 1 44.2ki q1% resistor (0603) r9 1 150ki q1% resistor (0603) r10 1 20ki q1% resistor (0603) r11 1 49.9ki q1% resistor (0603) r12 1 2.2i q5% resistor (0603) r13 1 4.02ki q1% resistor (0603) r15 1 10i q5% resistor (0603) r17 1 100i q1% resistor (0603) r18 1 50ki potentiometer (9.53mm x 4.83mm x 10.03mm) r19 1 24.9ki q1% resistor (0603) r20 1 220i q1% resistor (0603) u1 1 led driver (16 tssop-ep*) maxim max16833aue+ 1 led driver (16 tssop-ep*) maxim max16833baue+ 3 shunts 1 pcb: max16833 evaluation kit+ maxim integrated evaluates: max16833/max16833b max16833 evaluation kit
3 quick start required equipment ? max16833 ev kit ? 5v to 18v, 8a dc power supply ? a series-connected led string rated at 1a ? oscilloscope with a current probe procedure the ev kit is fully assembled and tested. follow the steps below to verify the board operation. caution: do not turn on power supply until all connections are completed. 1) verify that all jumpers (ju1, ju2, and ju3) are in their default positions, as shown in table 1. 2) connect the positive terminal of the dc supply to the vin pad and the negative terminal to the nearest pgnd pad. 3) connect the led string across the led+ and led- pads of the ev kit for buck-boost configuration (for boost configuration, connect the led string across the led+ and pgnd pads of the ev kit. the led string voltage should be higher than the input volt - age in this configuration). 4) clip the current probe on the wire connected to the led string. 5) turn on the dc power supply. 6) verify that the leds turn on. 7) verify that the oscilloscope displays approximately 1a. *default position. table 1. jumper descriptions (ju1, ju2, ju3) jumper shunt position description ju1 1-2* connects the ictrl pin of the max16833 to a voltage higher than 1.23v. the led current level is now using the internal reference. the shunt of ju2 must not be installed for proper operation. open disconnects the ictrl pin of the max16833 from the external voltage-divider on the vcc pin. allows the user to apply an external voltage to set the led current level. ju2 1-2 used only for the max16833b. for the max16833, this jumper is open. for the max16833b, this allows adjustment of the voltage on the ictrl pin by adjusting potentiometer r18. open* disconnects the ictrl pin of the max16833/max16833b from potentiometer r18. an external voltage between 0 and 5.5v can be applied to the ictrl pad. ju3 1-2* install for the default position for both the max16833 and max16833b. 2-3 allows dithering of the switching frequency to achieve spread spectrum for the max16833. the shunt of ju2 must not be installed for proper operation. open the voltage at the ictrl pin of the max16833 is determined by the voltage at the ictrl pad, or if ju1 is installed, the voltage-divider r7 and r8. maxim integrated evaluates: max16833/max16833b max16833 evaluation kit
4 detailed description of hardware the max16833 ev kit provides a proven design to evalu - ate the max16833 high-voltage hb led driver with inte - grated high-side current sense. the ev kit is set up for boost and buck-boost configurations and operates from a 5v to 18v dc supply voltage. the ev kit is configured to deliver up to 1a to a series led string. the string for - ward voltage can vary from 3v to 36v. analog dimming control (ictrl) when ju1 is installed, the ictrl pin is connected to the voltage-divider of r7 and r8, which sets the voltage at ictrl (v ictrl ) to 1.29v when input supply is above 7v and 890mv when the input supply is 5v. when v ictrl > 1.23v, the internal reference sets the led current (i led ) using the following formula: led 200mv i r4 = in the case of the ev kit, i led is set to 1a. if v ictrl < 1.23v, then v ictrl sets the led current level. alternatively, the analog dimming can be controlled by removing the shunt of ju1 and applying a voltage between 0 and 5.5v on the ictrl pad of the ev kit. pulse-dimming input (pwmdim) pulse dimming can be achieved by applying a pulsating voltage source on the pwmdim pad of the ev kit. when pwmdim is pulled low, dimout is pulled high and the pulse-width modulated (pwm) switching is disabled. frequency dithering (lframp) when ju3 is in the 2-3 position and ju2 is not installed, frequency dithering is achieved. frequency synchronization (rt/sync) the devices can be synchronized to an external clock by applying a synchronizing pulse on the rt/sync input pin. refer to the max16833/max16833b ic data sheet for more information regarding synchronizing to an external clock. frequency dithering must be disabled for external frequency synchronization. evaluating the max16833b for evaluating the max16833b, replace the max16833 on the ev kit with a max16833b. the jumper configura - tions are as follows: ju1 (open shunt position), ju2 (1-2 shunt position), ju3 (1-2 shunt position). see table 1 for details. maxim integrated evaluates: max16833/max16833b max16833 evaluation kit
5 figure 1. max16833 ev kit schematic maxim integrated evaluates: max16833/max16833b max16833 evaluation kit
6 figure 2. max16833 ev kit component placement guidecomponent side figure 3. max16833 ev kit component pcb layoutcomponent side 1.0? 1.0? maxim integrated evaluates: max16833/max16833b max16833 evaluation kit
7 figure 4. max16833 ev kit pcb layoutsolder side figure 5. max16833 ev kit component placement guidesolder side 1.0? 1.0? maxim integrated evaluates: max16833/max16833b max16833 evaluation kit
maxim integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a maxim integrated product. no circuit patent licenses are implied. maxim integrated reserves the right to change the circuitry and specifications without notice at any time. 8 maxim integrated 160 rio robles, san jose, ca 95134 usa 1-408-601-1000 ? 2012 maxim integrated products, inc. maxim integrated and the maxim integrated logo are trademarks of maxim integrated products, inc. revision history revision number revision date description pages changed 0 6/10 initial release 1 10/12 changed description for r4 in component list 2 evaluates: max16833/max16833b max16833 evaluation kit
|
